DSLRKIT 250M 10 Ports 8 PoE Switch Injector Power Over Ethernet NO Power Adapter

Description: DSLRKIT MID8P2U-E250 Passive PoE Injector Switch Support EXTEND mode, max Network Cable length to 250 meters Power supply not included Supports 12~55V DC power supply (Maximum current 4 amps) DC IN port 5.5X2.1mm, inside positive (+) outside negative (-) 10 Ports (2 Uplink, 8 PoE) 10/100Mbps Midspan Mode-B Unsolicited Power(4,5+/7,8-) Wall Mount NOTE. When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-8 network port will be reduced to 10Mbps for each one. Please check your IP CAMERA's bit stream setting. We recommend the value does not over 8Mbps(8192Kbps). (The up-link is not affected, it will always working at 100Mbps max speed) Notice! If you switch to the EXTEND mode, the Max allowable Network Cable length will increased to 250 meters. Then suggested buy 52V power adapter. This will avoids the power loss over the long distances, and will make sure the PoE IP Camera working. 52V Power adapter links: 52V1.85A http://www.ebay.com/itm/201863649634 52V2.7A http://www.ebay.com/itm/192137824001 48V Power adapter links: 48V2A http://www.ebay.com/itm/191880113415 48V3A http://www.ebay.com/itm/201384084416 This item do not include the power adapter, you need to buy an extra power adapter according to your requirement. So it only suitable for PoE professional customers. Please select the correct Power adapter by POE device， 802.3af (802.3at Type 1) PoE device, We suggest DC 48V power adapter. 802.3at Type 2 PoE+(plus) device, We suggest DC52V power adapter. Please refer to the Wikipedia "Power over Ethernet" section, under the "Standard implementation" paragraph. If your camera is with word “12V/PoE” as this picture shows, then please select 48V(or 52V) Power Adapter, do not select 12V Power Adapter. Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port: This is an Passive Power Over Ethernet of 10 port 10 / 100Mbps-T Ethernet switches, including 8 unsolicited PoE Ethernet ports and 2 Uplink ports. DC port apply 12~55V power supply adapter(not included), any one of the 8 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable. This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because "Power Link 1~8" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 1~8" port, this will damage your device. Gigabit(1000Mbps) ethernet device Please do not access "Power Link port" this will damage your device. Features: 10 x 10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 8-Ports PoE function Support EXTEND mode, max Network Cable length to 250 meters. Midspan Mode-B Unsolicited Power(4,5+/7,8-) Supports 12~55V DC power supply Each port supports auto MDI/MDIX, so there is no need to use cross-over cables. Full/half duplex transfer mode for each port. Specification: ALL Port: Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。 Power Link Port 1-8: any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs) Power LED LED ON: power on. LED OUT: power off Green Light LINK/ACT LED ON Indicates the port is connected to a network device and has been started LED OFF Indicates that this port is not connected to a network device or has not been started Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full-Duplex flow control Protocol CSMA/CD Ethernet Data Transfer Rate Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex) Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) IC Chips IC Plus IP178G + IP175G Network Media(Cable) 10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m) 100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) PoE Power on RJ45 Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8 DC Output: 12-55V, Per port Max 1A, Number of Ports 10 x 10/100Mbps Auto-Negotiation RJ45 ports with 8 PoE enabled (port-1 ~ port-8) Power Input Supports INPUT 12-55V DC power supply( Maximum current 4 amps) Power DC port 5.5 x 2.1mm, inside positive (+) outside negative (-) Power Consumption 3.2 Watts (max. no PD connected) According to the actual power consumption of equipment Temperature Operation Temperature:0 ~40℃ (32 ~104℉) Storage Temperature: -40 ~70℃(-40 ~158℉) Humidity Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing Product Dimensions 197mm W x 73mm D x 32mm H RAM Register Capacity 64K bytes per device MAC Address List 1K entries per device Frame Forward Rate 10Mbps Ethernet: 14880pps/Port 100Mbps Ethernet: 14880pps/Port Item Included: DSLRKIT MID8P2U-E250 10ports 8PoE Unsolicited(Passive) PoE switch x1 (Power supply not included) 12 Months Warranty from the date of purchase.

Price: 25.99 USD

Location: Shenzhen

End Time: 2024-08-19T10:27:54.000Z

Shipping Cost: 3.5 USD